ss1 hub nut removal.

Moderators: scimjim, philhoward, erikscimitardemon, Roger Pennington, Lukeyboy46

Post Reply
mikeh
Posts: 64
Joined: Tue Oct 27, 2009 9:55 pm
Location: tamworth
Been thanked: 1 time

ss1 hub nut removal.

Post by mikeh » Fri Sep 14, 2018 9:11 pm

I've been reading the other post regarding the hub nut size.
I'm in the process of building my two cars and need to remove the front and rear hubs to upgrade them.
The cars have had the rear axle removed and are on axle stands.
Any ideas on an easy wat to get them undone ?
When i get 5 mins i'll start a project thread as i've got loads of pics already.

Thanks

MIke



User avatar
scimjim
RSSOC Member
Posts: 35726
Joined: Sun Oct 01, 2006 10:08 pm
Location: Gloucester
Has thanked: 112 times
Been thanked: 819 times

ss1 hub nut removal.

Post by scimjim » Fri Sep 14, 2018 9:37 pm

I have removed a few hub nuts off the car and every one has been a total pain! I have some to do in the next few weeks and I think I’ll probably jam a scaffolding pole into the trailing arm and jam it into one of the barn pillars to counteract the torque of my 2’ 3/4” drive brace with a short scaffolding pole on the end.


Jim King

Current: SE5 (8Ball), TI SS1 (snotty), 1600 SS1 (G97), 1600 SS1 (C686CCR), 2.5TD SE5a (diesel 5a), 6 x random other SS1s.
Previous: SE5, 3 x SE5a, 2 x SE6a, 3 x SE6b, GTC, 2.9i GTC, 3 x 1600 SS1, 1300 SS1, Mk1 Ti Sabre, Mk1.5 CVH Sabre
Chief mechanic for: 1400 K series SS1 (Megan3), 1400 CVH EFi SS1 (Grawpy), Sabre/MX5 auto (The Flying Broomstick),
1300 SS1 (Number One) & Sarah's coupe.
CURE THE FAULT - NOT THE SYMPTOMS

User avatar
philhoward
RSSOC Member
Posts: 24002
Joined: Tue Aug 29, 2006 5:41 pm
Location: Staffs, UK
Has thanked: 41 times
Been thanked: 523 times
Contact:

ss1 hub nut removal.

Post by philhoward » Fri Sep 14, 2018 10:37 pm

I’ve been using an air impact wrench to get them off in the past - done it with just the front upright on the floor (not even in a vice) last time. Haven’t tried a rear hub yet but expect to be the same.

Takes a few goes of the rattler, but always got there.


Phil Howard
Scimitarweb Forum Admin
SS1 1600 Rooster Turbo; Sabre Mk1.5, Sabre Mk2
Previous: SE5/5a/SS1 No.1/SS1 Rooster/SS1 1800Ti/SE5a 24 Valve
http://www.ss1turbo.com
Never try and argue with an idiot. They drag you down to their level, then beat you based on experience.

User avatar
reliant-reviver
RSSOC Member
Posts: 4599
Joined: Thu Jun 14, 2007 8:05 pm
Location: Beighton, Sheffield
Has thanked: 68 times
Been thanked: 108 times

ss1 hub nut removal.

Post by reliant-reviver » Sat Sep 15, 2018 8:43 am

Rear hubs loose?
No worries!

Bolt wheel on.
Ratchet strap to pallet.
Breaker bar and shock loose.


Philip Andrew.
'74 Robin Super Saloon, '84 SS1 1300, '86 SS1 1800ti, '87 SS1 1300
Previous: I lost count around fifty.

rhss1
Posts: 34
Joined: Sat Sep 01, 2018 11:07 am

ss1 hub nut removal.

Post by rhss1 » Sun Sep 16, 2018 1:23 pm

My car is pretty much everything off it, the frame only has the suspension and differential still attached. What's worse is it's on a nice little trolley and rolls around.

The left front came off pretty easily, I had a bit of pipe over a 1/2 inch breaker bar and I braced my foot against the bottom B post to keep the frame still, and pulled hard suddenly.

The left rear I wedged a crowbar between the studs and the floor of the garage. Similar results.

For the tight right side hubs I'm going to drill a hole in a bit of steel pipe to go over one stud and use that as a brace against the ground.

[edit - a day or two later]

Pipe with a hole in it works a treat to hold the rear hub still.

I also supported the outboard end of the braker-bar with an axlestand. Six feet of bar on the socket and they came loose.
Last edited by rhss1 on Tue Sep 18, 2018 1:38 am, edited 1 time in total.



Clueless1
RSSOC Member
Posts: 107
Joined: Sun Feb 25, 2018 9:18 pm
Location: South Somerset
Has thanked: 11 times
Been thanked: 1 time

ss1 hub nut removal.

Post by Clueless1 » Sun Sep 16, 2018 6:32 pm

I’ve done mine today in readiness. The o/s were quite tight ( 13 stone jumping on a breaker bar tight), the n/s front was finger tight but the rear needed a lot of heat then a breaker bar. Hope that the rest of the suspension comes apart as easily 😁


Do or do not, there is no try.

Post Reply

Return to “SS1/SST/Sabre”