Search found 5410 matches

by AJL Electronics
Tue Dec 11, 2018 9:29 am
Forum: SS1/SST/Sabre
Topic: More stupid questions: axle stands, fuel hose and...
Replies: 7
Views: 177

More stupid questions: axle stands, fuel hose and...

Can anyone recommend a supplier of decent fuel hose that will last? Calling AJL Electronics ... Andy (AJL) has been selling Cohline hose for a while now and only sells one type - which is very much over-spec for the job but it’s a component you really don’t want to fail and it’s not really a job yo...
by AJL Electronics
Mon Dec 10, 2018 9:30 pm
Forum: Se6/6a/6b/GTC
Topic: Latest job in the workshop, chassis repairs
Replies: 7
Views: 374

Latest job in the workshop, chassis repairs

The completed repair section was then painted with weld through primer before being clamped into place. It is quite important to keep the heat to a minimum to prevent the foam burning or worse. I decided to use the thin metal technique which keeps distortion to a minimum in that case, but for me red...
by AJL Electronics
Mon Dec 10, 2018 9:18 pm
Forum: Se6/6a/6b/GTC
Topic: Latest job in the workshop, chassis repairs
Replies: 7
Views: 374

Latest job in the workshop, chassis repairs

Next the side rail and jacking point were welded up. I had intended to use a Rivnut in the corner but I wasn't happy with the fit. Remedy was to open the hole out and draw a 5/16" nut into it. Then it was welded up and the thread cleaned with a tap. The complete section was then test fitted again, f...
by AJL Electronics
Mon Dec 10, 2018 9:15 pm
Forum: Se6/6a/6b/GTC
Topic: Latest job in the workshop, chassis repairs
Replies: 7
Views: 374

Latest job in the workshop, chassis repairs

More offering up and shaping...
IMG_3056.JPG
IMG_3056.JPG (269.71 KiB) Viewed 97 times
IMG_3057.JPG
IMG_3057.JPG (190.02 KiB) Viewed 97 times
IMG_3058.JPG
IMG_3058.JPG (224.45 KiB) Viewed 97 times
by AJL Electronics
Mon Dec 10, 2018 9:13 pm
Forum: Se6/6a/6b/GTC
Topic: Latest job in the workshop, chassis repairs
Replies: 7
Views: 374

Latest job in the workshop, chassis repairs

I didn't need the whole piece, so I just cut it down to four inches. The side rail was also cut to suit. Temporary offering up of parts was achieved with a Lidl twin magnet. Fabulous thing, I even used it to clean my eye when I suspected a piece of swarf in it. In case there are any nannies looking ...
by AJL Electronics
Mon Dec 10, 2018 9:08 pm
Forum: Se6/6a/6b/GTC
Topic: Latest job in the workshop, chassis repairs
Replies: 7
Views: 374

Latest job in the workshop, chassis repairs

This is how the repair section is supplied. The jacking point is a fully sealed box, undrilled for the bolt or the drain hole. It is galvanised which I feel is a negative because it has to be ground off for welding.
IMG_3051.JPG
IMG_3051.JPG (246.09 KiB) Viewed 101 times
IMG_3049.JPG
IMG_3049.JPG (252.43 KiB) Viewed 101 times
IMG_3050.JPG
IMG_3050.JPG (218.36 KiB) Viewed 101 times
by AJL Electronics
Fri Dec 07, 2018 10:28 pm
Forum: Project Progress
Topic: Mikey Bikey's Scimega
Replies: 167
Views: 8075

Mikey Bikey's Scimega

I've never found them to grip very well , instead I use separate terminals and covers as per OEM and then use the correct crimping tools . A superior joint is achieved You must be buying poor quality then. I have never had any trouble with the grip of insulated crimps. The unreliability myth comes ...
by AJL Electronics
Fri Dec 07, 2018 9:49 am
Forum: Project Progress
Topic: Ben's (an emotional quandry) 1975 SE5a
Replies: 559
Views: 59311

Ben's (an emotional quandry) 1975 SE5a

A quick and easy test is to replace the oil filter. Might save all that work! If not, you have a spare ready primed for next time.
by AJL Electronics
Tue Dec 04, 2018 8:36 am
Forum: General Technical Discussion
Topic: About the new black EFL90 FORD oil filter
Replies: 24
Views: 1637

About the new black EFL90 FORD oil filter

Well all I can say is that the trade price for 10 off is more than you have paid.
by AJL Electronics
Tue Dec 04, 2018 8:26 am
Forum: Project Progress
Topic: The "Mighty" SE6 - Internal Recycling
Replies: 143
Views: 7891

The "Mighty" SE6 - Internal Recycling

You can also buy off my webshop, or give me an email / ring for anything else not listed.
by AJL Electronics
Mon Dec 03, 2018 1:07 pm
Forum: Project Progress
Topic: Heaven and Hell
Replies: 22
Views: 1442

Another recent job through the workshop SE6b

If it only happened once, I wouldn't worry about it. Maybe it was a bit gummed up so took a bit longer to free up? It is a special beast with two different seals on it. The bottom seal is very important apparently.
by AJL Electronics
Sun Dec 02, 2018 3:55 pm
Forum: Non-Technical Discussion
Topic: Beware the car thieves
Replies: 43
Views: 1523

Beware the car thieves

I met plenty during my prison work. They have a funny mentality. They have a hierarchy of their own and have the idea that one sort of scumbag is somehow morally superior to another, hence the need for Rule 43 etc. They also (as stated above) have no concience whatsoever. I recall getting on YO on h...
by AJL Electronics
Sun Dec 02, 2018 12:26 pm
Forum: Non-Technical Discussion
Topic: Beware the car thieves
Replies: 43
Views: 1523

Beware the car thieves

I'm with Corky though, if they want the car I want them to take it, without fear of threat or anguish to my family. I disagree. It is because people roll over and give in that these lowlives get away with it. At some point we have to stand up and say enough is enough. Even now most people at the sc...
by AJL Electronics
Sat Dec 01, 2018 6:38 pm
Forum: Non-Technical Discussion
Topic: Beware the car thieves
Replies: 43
Views: 1523

Beware the car thieves

That's why I ride a 13 year old BMW K1200LT. Only of interest to staid old men and wierdy beardies. ;-)

Go to advanced search