Search found 3986 matches

by Coupe Racing
Sat May 26, 2018 11:31 am
Forum: Project Progress
Topic: MR2 TDI
Replies: 196
Views: 17194

MR2 TDI

If using a pc then just drag the picture where you type the text
by Coupe Racing
Fri May 25, 2018 4:14 pm
Forum: Wanted
Topic: SE5 brake drum
Replies: 5
Views: 190

SE5 brake drum

Replied to you
by Coupe Racing
Thu May 24, 2018 11:09 am
Forum: Other Motorsport Discussion
Topic: Shelsley Walsh
Replies: 0
Views: 55

Shelsley Walsh

The JLR Formula E Grand Prix car is competing at Shelsley Walsh on 12 August
by Coupe Racing
Tue May 22, 2018 8:50 pm
Forum: Wanted
Topic: GTE parts wanted
Replies: 2
Views: 111

GTE parts wanted

I think I have a roll bar
by Coupe Racing
Tue May 22, 2018 6:55 pm
Forum: Wanted
Topic: SE5 brake drum
Replies: 5
Views: 190

SE5 brake drum

I have a pair of used drums here
No wear lip
Slight surface rust on shoe face
One drum has a small chip on the outer flange but does not impact on performance
by Coupe Racing
Tue May 22, 2018 11:11 am
Forum: Wanted
Topic: SE5 brake drum
Replies: 5
Views: 190

SE5 brake drum

Remind me of the dimensions please as I may have a good pair available
by Coupe Racing
Tue May 22, 2018 11:04 am
Forum: Se5/5a
Topic: Rear brake drums
Replies: 6
Views: 155

Rear brake drums

The point is answered and to quote one post in the link


“” the MGB studs are 7/16" UNF, and the Reliant brake drums are bespoke, and without a lot of re machining the MGB drums will not fit “”
by Coupe Racing
Sat May 19, 2018 9:35 am
Forum: General Technical Discussion
Topic: 1979 SE6A Limited Slip Diff
Replies: 5
Views: 181

1979 SE6A Limited Slip Diff

Best confirm it’s an LSD first before deciding what oil to use
by Coupe Racing
Fri May 18, 2018 10:49 am
Forum: General Technical Discussion
Topic: Turning the V6-engine by hand: how?
Replies: 17
Views: 457

Turning the V6-engine by hand: how?

AJL Electronics wrote:
Fri May 18, 2018 8:47 am
scimjim wrote:
Thu May 17, 2018 10:00 pm
Surely the two additional pullies should have holes in the centre so that you can get a long reach socket onto the crank bolt?
Autos are very awkward. Simplest is to use a socket on the alternator nut and keep the belt taut.

Like I said before and it is ideal once you get used to it
by Coupe Racing
Wed May 16, 2018 5:17 pm
Forum: Project Progress
Topic: Rat Rod (dizzy drama)
Replies: 1652
Views: 77339

Rat Rod (dizzy drama)

you can take the base plate out and put a standard one in with some points
by Coupe Racing
Wed May 16, 2018 1:25 pm
Forum: Project Progress
Topic: Rat Rod (dizzy drama)
Replies: 1652
Views: 77339

Rat Rod (dizzy drama)

Isn’t the distributor driven by the camshaft?
If the pencil shaft was not engaged there would be no oil pressure
by Coupe Racing
Wed May 16, 2018 11:48 am
Forum: General Technical Discussion
Topic: Turning the V6-engine by hand: how?
Replies: 17
Views: 457

Turning the V6-engine by hand: how?

manny wrote:
Wed May 16, 2018 9:23 am
i did it with a 3/8? socket on the crank bolt..i think?
5/8 from memory
by Coupe Racing
Wed May 16, 2018 7:22 am
Forum: Project Progress
Topic: Cherry SE5a
Replies: 5
Views: 253

Cherry SE5a

Probably lost in translation
Likely to be case hardened and ground or something similar
by Coupe Racing
Tue May 15, 2018 7:58 pm
Forum: General Technical Discussion
Topic: Turning the V6-engine by hand: how?
Replies: 17
Views: 457

Turning the V6-engine by hand: how?

Spark plugs out , a spanner on the alternator nut and adequate pressure on the fan belt
by Coupe Racing
Tue May 15, 2018 5:40 pm
Forum: Se6/6a/6b/GTC
Topic: Steering not centering after new rack
Replies: 37
Views: 1309

Steering not centering after new rack

hope they grease those trunions :shock: :?:

Go to advanced search